Flow Form Screwdriving – Trendspot at the AUTOMATICA 2014 / Innovative screwdriving system for vehicle bodywork production
(PresseBox) (Amberg, 28.07.2014) Whereas in the past, steel sheets were easy to join by spot welding or resistance welding, today this is no longer economical due to the modern material mix. The automobile industry is under pressure from legal requirements to reduce CO2 emissions, use lightweight construction and consequently to find alternative joining methods. Where access to both sides of the connection point is available this can be done using rivets. If however only one side is accessible then the well-established direct screwdriving flow form principle comes into use. A flow form screw is positioned on an aluminium or steel sheet without pre-drilled holes and the screwdriving process begins. The screw is applied with a high pressure down-force and rotates at high speed, generating a frictional heat which forms a crater through which the screw’s thread passes under reduced pressure. A machined thread is created, a normal screw can also pass through in the case of repairs. After the flow passage has been formed the speed is reduced and the screw is tightened to the head connecting surface and then the final tightening of the fastener to the pre-determined parameters of torque and angle takes place. The entire procedure usually takes less than two seconds. Additional fastening elements such as nut and bolts are not required as the assembly has been optimally adjusted to the passage and thread of the screw. The screw is fixed. There is no need for preparatory drilling or punching of the component.The screwdriving specialists DEPRAG SCHULZ GMBH u. CO. presented a live show on the topic of flow form screwdriving (FFS) at this year’s AUTOMATICA from the 3rd to the 6th of June in Munich under the slogan “Sheet Metal – Direct – Screw Assembly”. In Hall A6, exhibition stand 310 development, product and processing engineers from vehicle bodywork construction departments, but also from many other braches in which sheet metal is assembled such as white goods, can gain first hand information about the next generation of FFS.
What is new?
The DEPRAG engineers have successfully developed a freely programmable gear for a torque range of up to 15 Nm and speed range of up to 8000 rpm from two gears with 15 Nm at 6000 rpm and 12 Nm at 8000 rpm. As well as reduced investment costs, this also means a reduction in processing costs as replacement expenses do not apply.
The currently established FFS units usually shoot the flow drill screws tip first through the mouthpiece. Damage to the screw tip geometry is inevitable and can have devastating consequences. The required frictional heat which is necessary to penetrate the material cannot be generated. It is different in the new innovative DEPRAG flow form screwdriving unit: here the screw is shot in head first and an integrated revolver separator positions the screw so that its position is secured even for overhead assemblies. The next screw is reloaded already as the first screw is being seated. A decisive benefit in optimising the cycle time!
In developing this new generation further, years of operating experience have been incorporated. Jürgen Hierold, Sales Manager at DEPRAG explains, “Due to the complex geometry of bodywork the highest requirements for mobility of robots and the FFS unit are set. Combined rotation and pivoting movements of the robots are required in order to reach the screw assembly positions. Often the feedhose used can bend or twist so that the screws get stuck during loading. Massive disruptions to the assembly process, high risk to the processing reliability of the complete system and extensive fault clearance are the inevitable consequences. Therefore we were approached by one of the largest internationally active companies in the automobile industry with the demand for a system which presented screws without a feedhose. We have developed a magazine system for our customer which is based on three basic elements, the screw magazine, the magazine exchange station and the screw feeder”. Whilst one magazine is in operation, docked on the FFS unit systematically presenting 32 fasteners, the second magazine is being filled at the exchange station by the screw feeder. The screw feeder is outside the activity range of the robot, refilling screws without interference in the danger zone. If the first magazine is empty then a robot on the exchange station removes it to be refilled and replaces it with an already filled magazine so that assembly may continue. Thereby the best possible processing times are achieved with guaranteed processing reliability. “We now have this exchange magazine available as a standard solution. Even existing FFS systems can be simply and easily upgraded to include it”, explains Jürgen Hierold. (…)
via Joining sheet metal directly, quickly and simply – DEPRAG SCHULZ GMBH u. CO. – Pressemitteilung.